Configure LLDP-MED Civic Address Location Information
About this task
Perform the following procedure to configure civic address location information of local LLDP-MED on specific ports.
Procedure
-
Enter GigabitEthernet Interface
Configuration mode:
enable
configure terminal
interface GigabitEthernet {slot/port[/sub-port][-slot/port[/sub-port]][,...][slot/all][all]}
Note
If the platform supports channelization and the port is channelized, you must also specify the sub-port in the format slot/port/sub-port.
- Configure the civic
address location by configuring the country-code and at least one
other location parameter:
lldp location-identification civic-address country-code WORD<2-2> (additional-code additional-information apartment block building city city-district county floor house-number house-number-suffix landmark leading-street-direction name place-type pobox postal-community-name postal-zip-code room-number state street street-suffix trailing-street-suffix) WORD<0-255>
Note
If you try to configure a civic-address with a large number of arguments, 26 or more, the command fails and a software message informs you to split the command into multiple smaller commands.
Example
Configuring civic address location on port 2/1:
Switch:1>enable Switch:1#configure terminal Switch:1(config)#interface gigabitEthernet 2/1 Switch:1(config-if)#lldp location-identification civic-address country-code US city New York
Variable Definitions
The following table defines parameters for the lldp location-identification civic-address command.
|
Variable |
Value |
|---|---|
|
additional-code WORD<0–255> |
Specifies the location information parameters. |
|
additional-information WORD<0–255> |
Example: South Wing |
|
apartment WORD<0–255> |
Example: Apt 42 |
|
block WORD<0–255> |
Specifies a block, e.g. 3 |
|
building WORD<0–255> |
Example: Low Library |
|
city WORD<0–255> |
Specifies a city, e.g. Sunnyvale |
|
city-district WORD<0–255> |
Specifies a city district, e.g. Santa Clara |
|
country-code WORD<2–2> |
Specifies a country using a 2 character string, example US (United States), CA (Canada). |
|
county WORD<0–255> |
Specifies a county, e.g. Alameda |
|
floor WORD<0–255> |
Example: 8 |
|
house-number WORD<0–255> |
Specifies a house number, e.g. 123 |
|
house-number-suffix WORD<0–255> |
Specifies a house number suffix, e.g. A, 1/2 |
|
landmark WORD<0–255> |
Specifies a landmark, e.g. Columbia University |
|
leading-street-direction WORD<0–255> |
Specifies a leading street direction, e.g. N |
|
name WORD<0–255> |
Example: Joe‘s Barbershop |
|
place-type WORD<0–255> |
Example: office |
|
pobox WORD<0–255> |
Example: 12345 |
|
postal-community-name WORD<0–255> |
Example: Leonia |
|
postal-zip-code WORD<0–255> |
Specifies a postal or zip code, e.g. 95054 |
|
room-number WORD<0–255> |
Example: 450F |
|
state WORD<0–255> |
Specifies a state, e.g. NJ, FL |
|
street WORD<0–255> |
Specifies a street, e.g. Great America Parkway |
|
street-suffix WORD<0–255> |
Specifies a street suffix, e.g. Ave, Blvd |
|
trailing-street-suffix WORD<0–255> |
Specifies a trailing street suffix, e.g. SW |